Search Our Site

Become a Program Member!

CONSTELLATION NUCLEAR, LLC
NINE MILE POINT NUCLEAR POWER STATION, LLC

Mechanical Maintenance

• Organization Directory Page
  (titles of all evaluated learning experiences, organization description, and source of official student records)

• Titles of all evaluated learning experiences in the Mechanical Maintenance section

• Descriptions and credit recommendations

Titles, descriptions, and credit recommendations for all learning experiences recommended for college credit within the Mechanical Maintenance section can be found below. To locate information on additional learning experiences, which have also been recommended for college credit, use the Organization Directory Page link above for a complete list of titles for all learning experiences or use the following links to go directly to other sections: 

Auxiliary Operator Training
Chemistry/Radiation Protection Training
Electrical Maintenance
General Courses
Instrumentation and Controls
Reactor Operator/Senior Reactor Operator Training

Titles of all evaluated learning experiences in the Mechanical Maintenance section

NOTE: When a credit recommendation is no longer active, the course description may be abbreviated. The last edition of the Directory in which complete information can be found is indicated on the course exhibit. Complete information can also be obtained by contacting National PONSI.

Alignments (MM3-INIT-307)
Air Compressors (MM3-INIT-215)
Air-Hydraulic Valve Operators (MM3-INIT-327) (Introduction to Mechanics I)
Basic Fans, Blowers, and Air Compressors (MM3-INIT-206)
Basic Hydraulics (MM3-INIT-161)
Basic Pneumatics (MM3-INIT-160)
Bolting and Fastening (MM3-INIT-216) (Introduction to Mechanics II)
Heat Exchangers (MM3-INIT-159)
Heat Exchangers, Condensers, and Tubes (MM3-INIT-159)
Lubrication and Bearings (MM3-INIT-112)
Measuring Tools (MM3-INIT-104)
Oxygen-Acetylene Cutting (MM3-INIT-156A)
Pipefitting (MM3-INIT-305)
Shielded Metal-Arc Welding (MM3-INIT-156B)
Welder Helper Skills (MM3-INIT-217)
Welder Skills (MM3-INIT-217)

Descriptions and credit recommendations

MECHANICAL MAINTENANCE

Alignments (MM3-INIT-307)
Dates: December 1991 - May 1997.
Credit recommendation: In the lower division baccalaureate/associate degree category, 1 semester hour in Metrology (5/92). NOTE: Complete information on this course last appeared in the 2000 edition.

1. Basic Pneumatics (MM3-INIT-160)
2. Basic Hydraulics (MM3-INIT-161)
3. Air Compressors (MM3-INIT-215)
(Formerly Basic Fans, Blowers, and Air Compressors [MM3-INIT-206])
4. Air-Hydraulic Valve Operators (MM3-INIT-327)
(Introduction to Mechanics I)
Dates: 1. February 1991 - May 1997. 2. May 1991 - May 1997. 3. June 1991 - May 1997. 4. May 1992 - May 1997.
Credit recommendation: Courses 1, 2, 3, and 4: In the lower division baccalaureate/associate degree category, 3 semester hours in Engineering Technology or Plant Utilities Technology (5/92). NOTE: Courses 1, 2, 3, and 4 must all be completed to receive credit. NOTE: Complete information on these courses last appeared in the 2000 edition.

1. Heat Exchangers, Condensers, and Tubes (MM3-INIT-159)
(Formerly Heat Exchangers [MM3-INIT-159])
2. Lubrication and Bearings (MM3-INIT-112)
3. Measuring Tools (MM3-INIT-104)
4. Bolting and Fastening (MM3-INIT-216)
(Introduction to Mechanics II)
Dates: 1. May 1991 - May 1997. 2. May 1991 - May 1997. 3. January 1992 - May 1997. 4. March 1991 - May 1997.
Credit recommendation: In the lower division baccalaureate/associate degree category, 1 semester hour as a mechanical laboratory/shop in Mechanical Technology (5/92). NOTE: Complete information on these courses last appeared in the 2000 edition.

Pipefitting (MM3-INIT-305)
Dates: May 1992 - May 1997.
Credit recommendation: In the associate degree/certificate category, 2 semester hours in a Plumbing and Heating curriculum (5/92). NOTE: Complete information on this course last appeared in the 2000 edition.

1. Welder Skills (MM3-INIT-217)
(Formerly 1. Welder Helper Skills [MM3-INIT-217] and 2. Shielded Metal-Arc Welding [MM3-INIT-156B])
2. Oxygen-Acetylene Cutting (MM3-INIT-156A)
Dates: Version 1: 1. August 1991 - September 1993. 2. June 1991 - September 1993. 3. June 1991 - September 1993. Version 2:1. October 1993 - May 1997. 2. October 1993 - May 1997.
Credit recommendation: Version 1, Courses 1, 2, and 3 or Version 2, Courses 1 and 2: In the associate degree/certificate category, 2 semester hours as an Introduction to Welding shop (5/92). NOTE: Courses 1, 2, and 3, Version 1 must all be completed to receive credit; Courses 1 and 2, Version 2 must both be completed to receive credit. NOTE: Complete information on these courses last appeared in the 2000 edition.

Updated 2/2/04

Return to all CCR Online  listings